How to Set Up Bitmain Antminer D7? Basic Guidelines

How to Set Up Bitmain Antminer D7 Basic Guidelines

The instructions in the guide below will help you configure your Bitmain Antminer D7 so you can start mining DASH.

Welcome to our Antminer D7 blog! In this post, we’ll provide you with a step-by-step guide on how to set up your Bitmain Antminer D7 for efficient dash mining. Setting up your mining rig correctly is crucial for maximizing profitability and success in the cryptocurrency market.

Let’s get started!

What is Antminer D7?

Antminer D7 – assembled on a 7nm chip model for mining algorithm X11 For a while, it was believed that this type of cryptocurrency was safe from ASIC miners, but Bitmain disproved this theory first with the release of D3, followed by the series D7, which significantly outperformed the competition. As a result, the manufacturer is not in a rush to introduce new modifications.

Specifications Antminer D7:

  • Working algorithm: X11
  • Hash rate: 1286 GH/s
  • Power Consumption: 3148 W
  • Energy Efficiency: 0.48 J/GH
  • Working Temperature: 5-40C
  • Overall dimensions: 290x196x400
  • Weight of equipment: 15.8 kg
  • Noise level: 75dB
  • Cooling system: Air

Bitmain Antminer D7 Overview

The most recent model from Bitmain is the D7 server. D7 server includes the APW12 power supply. To guarantee simple setup, all D7 servers are examined and set up before shipping.


  1. Please place your goods in use according to the above layout in case of damage.
  2. An earthed mains socket-outlet must be used to connect the equipment. The socket-outlet must be installed close to the machinery and should be simple to use.
  3. The two power supply sockets on the equipment must be connected simultaneously in order for it to function. Make sure to turn off all power inputs after the equipment has been powered down.
  4. DO NOT remove any cables or screws that are fastened to the product.
  5. NOTHING SHOULD BE PRESSED on the cover’s metal button.
  6. Please take note that the actual server will take precedence.-

1.1 D7 Server Components

The main components and controller front panel of D7 servers are shown in the following figure:


Please see the images above to see the differences between the two control panels for the SD Card Slots.

APW12 Power Supply:


  1. D7 server includes the APW12 power supply. Please see the following specifications for more information on the specific parameters.
  2. There are two more power cords required.

1.2 Specifications

Version: D7 1286GH/S

Model No.: 240-Cm

Product GlanceValue
Hashrate, GH/S1286
power on wall@25℃, Watt3148
power efficiency on wall @25°C, J/G2.4
Server Size (Length*Width*Height, w/o package), mm(1-1)400*195.5*290 mm
Net weight, kg (1-2)14.5


(1-1) Including PSU size.

(1-2) Including PSU weight.D7 Server Installation Guide

Set Up a New D7

Before using a new D7, you must check the miner and be aware of the necessary safety precautions. The steps for configuring your new D7 are listed below.

I. Before Using

  • Inspect the new miner

1. Visually inspect the box after receiving your miner package. Search for signs of damage. Take pictures of the package’s condition if it is damaged before opening it and looking at the miner inside. If the miner is also damaged, give customer service a quick call.

2. Examine the miner for aesthetic flaws. Check the corners of the miner for dents and cracks. Keep an eye out for broken cables and fan blades. If you discovered any damage or defects, kindly contact customer support right away.

3. For the miner, check the heat sinks. the miner’s front and back fans’ heat sinks should be inspected for any loose parts. Get in touch with customer service right away if you notice any loose heat sinks.

  • Know the precautions for the use

1) PoE is not supported.

2) Only Ethernet network connections can be made with the aid of a router or switch.

3) Use the miner where the temperature ranges from 25 to 35 degrees Celsius.

4) Keep the miner’s surrounding humidity below 65%

5) Keep the miner clean and free of catkins to prevent corrosion and/or heat buildup.

6) The supported web browsers are Chrome and Firefox.

7) The power connector and PSU cord need to be plugged in firmly.

II. Unboxing and Initial Setup

  1. Unpacking the Antminer D7:
    • Carefully unpack the Antminer D7 and ensure that all components are included.
    • Take note of any special instructions or safety precautions mentioned in the user manual.
  2. Connecting necessary cables and accessories:
    • Connect the power supply unit (PSU) to the Antminer D7, ensuring a secure connection.
    • Connect the Ethernet cable to the miner for network connectivity.
  3. Configuring network settings:
    • Power on the Antminer D7 and connect it to your local network.
    • Identify the miner’s IP address using your router or IP scanning software.
    • Access the web-based user interface using the IP address in a web browser.

III. Setting Up Bitmain Antminer D7 Server

To set up the server:

The file can only be opened with Microsoft Windows.

1. can be downloaded from this page.

2. Extract the file.

IP addresses are automatically distributed by the DHCP network protocol by default.

3. Right-click IPReporter.exe and run it as Administrator.

4. Select one of the following options:

■ To designate where farm servers should be placed, use the words Shelf, Step, and Position.

■ Standard; appropriate for home servers.

5. Click Start.

6. The IP Report button on the controller board should be clicked. For about five seconds, hold it down until it beeps.

On the screen of your computer, a window containing the IP address will be visible.

7. Enter the provided IP address into your web browser.

8. Continue by entering root as the username and password.

An optional Static IP address can be assigned in the Protocol section.

9. Type in the IP address, Subnet mask, gateway, and DNS server.

10. Click “Save”.

IV. Configuring Mining Pools

Setting up the Pool

To configure the server:

  • Click Settings marked below.


Although the fan speed percentage can be changed, we advise leaving it at the default value. If the fan speed percentage hasn’t been chosen yet, the server will change the fan speed automatically.

  • Set the options according to the following table:
Mining addressGive the location of the pool you want to use.Three mining pools can be configured on the D7 servers, with the first pool (pool 1) having lower priority than the third pool (pool 3). If none of the pools with higher priority are available, the lower priority pools will only be used.
NameYour employee ID for the chosen pool.
Password (optional)The chosen employee’s password.
  • After configuring, press Save.

V. Monitoring Bitmain Antminer D7 Server

To check the operating status of your server:

  • To view the server status dashboard, click the link below.

Note: The D7 server operates at a fixed frequency of 625 MHz. Firmware will stop running when the Temp (Outlet) reaches to 75℃,there will be an error message “over max temp, pcb temp (real-time temp)” shown on the bottom of kernel log page. Meanwhile, the server temperature on the dashboard interface turns to abnormal and shows “Temp is too high”.

  • Monitor your server according to the descriptions in the following table:
Number of chipshow many chips were found in the chain.
FrequencyASIC frequency configuration.
Real HashrateEach hash board’s current hash rate, expressed in GH/s.
Inlet Temp(deg. C) Inlet temperature
Outlet Temp(deg;C) The outlet’s temperature
Chip stateOne of the following statuses will appear:· The Green Icon – indicates normal· The Red Icon– indicates abnormal

VI. Administering Bitmain Antminer D7 Server

6.1 Checking Your Firmware Version

To check your firmware version:

  1. Locate the Antminer D7 firmware version at the bottom of your server’s backstage.
  2. Firmware Version displays the date of the firmware your server uses. The server in the examples below is running firmware version 20210827.

6.2 Upgrading Your System

In order to complete the upgrade, make sure the D7 server is still powered on. You will need to send it back to Bitmain for repairs if the power goes out before the upgrade is finished.

To upgrade the server’s firmware:

  1. In System, click Firmware Upgrade.
  2. Administering Your Server
  3. For Keep Settings:

■ Select “keep settings” to keep your current settings (default).

■ Unselect “keep settings” to reset the server to default settings.

4. Navigate to the upgrade file after clicking the button. Select the upgrade file, then click Update.

5. Restart the server after the upgrade is finished, and it will go to the settings page.

6.3 Modifying Your Password

To change your login password:

  1. In System, click the Password tab.
  2. Set your new password, then click Save.

6.4 Restoring Initial Settings

To restore your initial settings

  1. Set the server to “on” and give it five minutes to run.
  2. On the controller front panel, press and hold the Reset button for 10 seconds.

Your server will reboot and return to its factory default settings if you reset it. When the reset is successfully performed, the red LED will automatically flash once every 15 seconds.

VII. Fine-tuning and Optimization

  1. Adjusting hash rate and power settings:
    • Optimize your mining performance by adjusting the hash rate and power consumption settings.
    • Find a balance that maximizes profitability while maintaining stability.
  2. Monitoring temperature and fan speed:
    • Keep a close eye on the temperature of the Antminer D7 to prevent overheating.
    • Adjust fan speeds if necessary to maintain optimal operating conditions.
  3. Implementing cooling solutions for efficient operation:
    • Consider additional cooling measures, such as using external fans or setting up the miner in a cool environment.
    • Proper cooling can improve the lifespan and performance of your mining rig.

VIII. Troubleshooting Common Issues

  1. Identifying and resolving connectivity problems:
    • If you encounter connectivity issues, check the network cable, IP settings, and firewall settings.
    • Restart the Antminer D7 and your network equipment if necessary.
  2. Dealing with hardware or software errors:
    • Keep an eye out for error messages or abnormal behavior on the dashboard.
    • Consult the user manual or manufacturer’s resources to troubleshoot and resolve specific errors.
  3. Seeking assistance from Bitmain support or online communities:
    • If you encounter persistent issues, reach out to Bitmain support or engage with online communities for advice and solutions.

IX. Best Practices for Maintenance

  1. Regular cleaning and dust prevention:
    • Clean the Antminer D7 regularly to prevent dust accumulation and maintain optimal performance.
    • Use compressed air or soft brushes to clean the fans, heatsinks, and other components.
  2. Updating firmware for performance enhancements:
    • Stay updated with the latest firmware releases from Bitmain.
    • Check for firmware updates periodically and apply them to benefit from performance improvements and bug fixes.
  3. Monitoring profitability and adjusting mining strategy:
    • Keep track of your mining profitability and adjust your mining strategy accordingly.
    • Stay informed about market trends and adjust settings or switch to different cryptocurrencies when necessary.

Conclusion: Set Up Antminer D7

Congratulations on successfully setting up your Bitmain Antminer D7 for dash mining! By following this comprehensive guide, you have equipped yourself with the knowledge and steps needed to start your mining journey. Remember to maintain your mining rig, stay updated, and adapt your strategy to maximize your mining rewards. Happy mining!

Scroll to Top